Baileigh Heavy Duty Hydraulic Shears

Made in Taiwan

The SH-5203-HD from Baileigh Industrial is a heavy duty shear that can take anything you can throw at it.  The industrial grade hydraulic system is designed to shear up to 1/4 inch mild steel over its whole length of 52 inch.  Designed like the rest of the Baileigh Industrial shear line the SH-5203-HD uses only the best components and building practices to ensure a machine that will outlast you.  The frame is made from fully welded plate steel for increased rigidity and prolonged blade life.  Blades can be flipped and sharpened many times saving you money.

Operation of the SH-5203-HD is very simple, just push the foot pedal and the hydraulic hold downs grab the material to ensure a straight cut.  The blade drops and shears the material.   A control panels allows for rake adjustment, jog/run/stop controls, production counter, and much more. This Heavy duty shear can be run in the jog mode, single cycle mode, or continuous cycling mode.  There is also an easy to use adjustable blade gap lever that can be changed in seconds when changing thickness.  A convenient shadow line position rounds out the feature of the SH-5203-HD.

For more information on the SH-5203-HD heavy duty shear contact a representative today.

SH-5203-HD-NC Heavy Duty Metal Cutting Shear

Built for years of heavy cutting, this numerically controlled shear makes industrial production runs more efficient. Blade gap and rake angle adjustment ensure high cut quality.

• Cuts up to 52 inch-wide sheet metal.
• Maximum capacity of 1/4 inch mild steel.
• 15 hp motor runs on 220-volt 3-phase power.
• Upper blade carriage that rides in a 3-axis bearing housing.
• Heavy-duty precision ground and hardened rail system gives you unbeatable accuracy and long blade life.
• Front and rear supports and side guides help you keep material square to the blade.
• Roller infeed table makes it easy to maneuver heavy plate steel for the next cut.
• 8 hydraulic hold-downs provide 3.2 tons of pressure each, preventing sheet metal from lifting.
• Programmable quick-change backgauge rides on a screwball rail system with a positioning encoder.
• Switch between 3 modes as needed:
  • Jog mode: Inching the blade down to the material.
  • Single cycle mode: One cut for one pedal push.
  • Automatic cycling mode: Continuously cutting for production runs.
• Piece counter makes it simpler to do production runs.
• Remote operator control pendant houses an E-Stop button and foot pedal controls.
• Simple handle lets you adjust the blade gap in seconds to avoid crimping or folding, particularly with thinner material.
• Adjustable rake angle can change for your material thickness, giving you cleaner cuts and reducing strain on the hydraulics.
• It’s simple to set the rake angle: just hit a button, move the lever, and a light goes on when you reach the correct angle.
• High carbon chromium blades that have several edges (2 on top, 4 on bottom), so you can flip them several times before you need to resharpening.
• Shadow light stretches the entire length of the web width for proper placement of the beginning of the cut, for those one-off shearing requirements.
• Fully welded plate steel framework maintains stability, reduces flex, and minimizes burr.
• Covered by a 1-year parts warranty.
• We stock blades and replacement parts at our Wisconsin warehouse; we can ship them out quickly

Made in Taiwan

At 28 strokes per minute the SH-5208-HD hydraulic metal cutting shear is truly a workhorse that you must have in your shop.  The SH-5208-HD has a shearing capacity of 8 gauge (11/64 inch) mild steel over its entire length of 52 inch, making it perfect for these 4x8 ft sheets of metal that are commonly found at steel suppliers.

The SH-5208-HD is built for heavy duty production, this machine has thick steel plate frame that is fully welded for rigidity.  The shearing carriage rides against hardened carriage ways and uses heavy duty bearings to reduce friction and wear. The industrial grade hydraulics system on the SH-5208-HD is powered by a 10 hp 220 volt three phase motor.

Operation of the SH-5208-HD is easy; the centralized control panel offers the selection of jog, single or continuous cutting modes.  A showdown line helps to line up the next cut for accuracy.  There is also a dial for adjusting the rake that eliminates curl and twist in cutting as well as a quick adjustment lever for material thickness.  The upper blade is two sided while the lower blade is four sided. The blades can be resharpened when needed saving money.  A back gauge, roller tables and side gauges round out this great package.

For more information on the SH-5208-HD Hydraulic metal cutting shear, contact a representative today.

Made in Taiwan

The SH-5210-HD heavy duty hydraulic shear is a heavy duty machine built for years of production. It will take what you can throw at it and keep coming back for more.  This machine has thick steel plate frame that is fully welded for rigidity.  The shearing carriage rides against hardened carriage ways and uses heavy duty bearings to reduce friction and wear. The industrial grade hydraulics system on the SH-5210-HD is powered by a 7.5 hp 220 volt three phase motor.

The centralized control panel offers the selection of jog, single or continuous cutting modes. There is also a dial for adjusting the rake that eliminates curl and twist in cutting as well as a quick adjustment lever for material thickness.  The upper blade is two sided while the lower blade is four sided. The blades can be resharpened when needed saving money.

This hydraulic sheet metal cutting shear has rigid, heavy duty load table and side gauges.  A light shadow line for shearing position is standard and st the rear of the machine is a manual back gauge for repeatability.  For more information on the SH-5210-HD heavy duty hydraulic shear, contact a representative today.

The SH-70250-HD from Baileigh Industrial is a hydraulic shear that cuts 1/4 inch mild steel over its entire 70 inch length.  The frame of the SH-70250-HD is all integrated and fully welded to eliminate vibrations commonly found on other models.  By eliminating vibrations, it is eliminating any strees that can occur during the cutting process.

The SH-70250-HD features an NC controller for programming of the back gauge.  This programmer is accurate to =/- .01mm and can hold up to 100 programs.  Convenient rolling tables mounted on the front of the machine help with loading of materials.  Gap is easily adjusted via hand wheels.

Since the SH-70250-HD hydraulic shear is built to last, Baileigh Industrial uses only the best quality components, Schneider electrical, Rexroth hydraulic systems, and NOK seals from Japan.