PTO-powered centrifugal pump for Ventrac/Steiner Tractors
TrunkPump's Ventrac/Steiner model mounts in less than a minute, with no tools, to your Ventrac or Steiner tractor to make quick work of your next pumping job. Hoses stay attached as your tractor
gets right to the problem. The fast priming pump is fantastic for repeat applications in a variety of hard to reach situations
DEWATERING PUMP
TP-3VS: Ventrac/Steiner 3â Dewatering Pump
Shown with attached discharge hose.
Use for a wide range of water/liquid transfer/evacuation applications where volume is important; uses Ventrac/Steiner tractor to get past steep slopes and rough uneven terrain with a light
footprint.
Pump: 3" self-priming reinforced polyester centrifugal pump with EPDM rubber coated volute and seals, plastic impeller and stainless steel internal hardware. Iincludes belts and pulley cover.
Pulleys: Cast Iron A/B Combination; Sealed Idler Bushing
Frame: TGIC Powder Coated Steel
Dimensions: 29" L x 26" W x 16" H
Weight: 73 lbs.
Performance: 310 gpm, up to 37 psi
FAQ - Frequently Asked Questions
Why should I choose TrunkPump?
Low maintenance and ease of use are the main reasons. If you do not like maintaining a gas-powered pump and are tired of lugging one around, TrunkPump might be the right choice for you.
So, it just hooks up to my tractor?
Yes, it attaches to your Category 1 three-point hitch and is powered by the Power Take Off (PTO).
What about horsepower requirements?
Our largest pump (4 inch) requires 15hp, the others only 8hp. Most compact tractors have more than enough power to run a TrunkPump.
Sounds pretty simple, how does it work?
It is simple, by design. TrunkPump takes the power from your tractor, reverses the rotation and increases rpms from 540rpm up to 3500rpm to power the pump. All this is done on a sturdy platform for
easy and safe transport.
What is this I hear about a hydraulic version?
After years of requests we now offer a hydraulically driven model that is powered by the remote hydraulics from a variety of compact equipment from a Bobcat down to the Dingo that ate my
baby.
Are there any special requirements for the hydraulic model?
The hydraulic model requires 9gpm of hydraulic flow at 1250psi.
What if I have got less or more flow than that?
If you got less flow the pump will run at low speed and not work properly. If you have more flow our priority flow manifold sends a priority flow of 9gpm/1250psi to the pump and the excess returns
to your hydraulic source.
HOSE PACKAGES
Complete the TrunkPump with reinforced PVC suction hoses and PVC lay-flat discharge hoses. Custom lengths available upon request.
HP-3PT: 3" x 7' "Trunk" Suction Hose, 3" x 25' Discharge Hose, CS-3 Strainer w/ Elbow
HP-3LG: 3" x 20' Suction Hose, 3" x 25' Discharge Hose, CS-3 Strainer w/ Elbow
CUSTOM STRAINERS
Keep out unwanted trash and pump in shallow water to 1/2" with our custom Deep Draw Strainer or pump in shallow water to 1/4â (basements, precious turf) with our Top-Hole Strainer.
CS-3: 3" Shallow Water Strainer 1/2" Depth w/ 90° Elbow
SS-3: 3" Top-Hole Strainer 1/4" Depth w/ 90° Elbow
NOZZLE PACKAGES
Connect to discharge hose for pressure applications such as washing equipment, fire fighting, irrigation, etc.
NP-3: for 3" pumps, reduced to adj. flow nozzle (1-1/2")
FUEL SAVINGS KIT
The Fuel Savings Kit modifies 3-Point models to pump at full capacity with throttle at 60% to conserve fuel.
FSK-1: Fuel Savings Conversion Kit
