DAKE Euromatic 370S Coldsaw

models
350SA
Euromatic 370S
Euromatic 370S-L

SEMI-AUTOMATIC/FULLY AUTOMATIC COLD SAW
974355	Super 350 SA	14" Semi-Automatic Cold Saw, 220v-3 ph 3 speed (add $940 for 440v)
SEMI-AUTOMATIC COLD SAWS
976200-2	Euro 370 S	Semi-Automatic Cold Saw, Ferrous Head, 220v-3 ph (add $940 for 440v)
976202-2	Euro 370 S-L	Semi-Automatic Cold Saw, Non-Ferrous Head, 220v-3 ph (add $940 for 440v)
COLD SAW ACCESSORIES
300674	Transformer	440 Volt Transformer
AAL3100L	AAL3100L	Pneumatic Vise Models 315 - Factory Installed
AAL3100L	AAL3100L	Pneumatic Vise Models 315 - For Field Installation
79827	79827	Pneumatic Vise Model 350 CE - Factory Installed

300128	300128	Ferrous Cutting Head for Mounting on Non-Ferrous Saw
79917	79917	Non-Ferrous Cutting Head for Mounting on Ferrous Saw
301644	301644	78 inch Loading Table All Thomas Modesl In-bound with protective cover plates
301645	301645	78 inch Un-loading Table All Thomas Modesl Out-bound with scale and adjustable positive stop
716602	716602	60 inch Roller Table 301169 Transformer 575 Volt Transformer

Click here to download manual

Click here to download parts list

Semi-Automatic Cold Saws
Model 350SA 14 inch blade

Semi-automatic cold saw that has a push-button or foot switch activation, an oversized pedestal base, shroud enclosed head feed cylinder, adjustable pneumatic vise. Variable speed controlled by a frequency inverter increases the material cutting range.

440V model requires step-down transformer for operation (part number: 300674)

Warning: This product contains Nickel, a chemical known to the State of California to cause cancer.

Features:

Push button or foot-switch activation to avoid operator fatigue.
Shroud enclosed head feed cylinder with sliding cams for fast cutting stroke adjustment.
Additional ball bearing support of hardened and ground spindle shaft to prevent failure.
Adjustable pneumatic vise with sliding gib to true up clamping under blade with 1/4 stroke.
Oversized pedestal base to reduce vibration.
Head rotates 45 deg right and 60 deg left of center for easy miter cutting.
Removable hardened, serrated vise jaw faces.
Ability to add a programmable feed system to make fully automatic with wide range of capabilities.

Standard Equipment

Blade
Coolant
Saw blade selector calculator
Tools kit for changing blades
Instruction and service manual
Adjustable positive stop

Specifications
Model Number	350SA
Voltage	220 V/440 V, 3-Phase
Horsepower	3.5 max
Cutting Ability	Ferrous/Non-Ferrous/Plastic
Maximum blade diameter	14 inch
Maximum vise opening	6-5/8 inch
Maximum feed vise opening	n/a
Maximum Angle	60 deg left/ 45 deg right
Slotting	No
Phase	3
Speeds	20-105 rpm
Weight	890 lbs
Solid round 90 deg capacity	3-3/8 inch
Solid round 45 deg capacity	3 inch
Tube 90 deg capacity	4-3/4 inch
Tube 45 deg capacity	4 inch
Square 90 deg capacity	4-1/8 inch
Square 45 deg capacity	3-3/8 inch
Rectangle 90 deg capacity	6-1/4 x 3-1/2 inch
Rectangle 45 deg capacity	3-3/8 x 2-3/4 inch
Work height	36-3/4 inch
Height	60 inch
Width	33 inch
Depth	50 inch

Euromatic 370S Ferrous

Click here to download manual

Click here to download parts list

Semi-Automatic Cold Saws

Model Euromatic 370S Ferrous 14.5 inch blade

Semi-automatic ferrous saw that's user friendly for set up and operation. Featuring two removable surface wear plates, heads that rotate 45Âº and 90Âº left/right, three gib guides, a manual oiler, and a self-adjusting, metal chip brush.

440V model requires step-down transformer for operation (part number: 300674)

Warning: This product contains Nickel, a chemical known to the State of California to cause cancer

Features:

Head rotates 45 deg right of center for miter cutting and up to 90 deg left of center for miter cutting and slotting.
Outboard section of the table is designed so shorter lengths tumble down a mesh discharge chute.
Manual oiler to lubricate 1 inch thick, hardened vertical ways.
3.5/4.5 HP motor has the muscle to drive a 14-1/2 inch or 12 inch blade quickly and quietly through solids.
Clear acrylic hood has shock assists for raising and lowering and electrical interlocks.
Table features two removable surface wear plates to support longer cut lengths.
Three gib guides for the cutting head with two adjustable cast iron gib blocks in each for increased cutting accuracy and easy adjustment.
Rear surface of the gearbox is machined with interlocking circles to evenly distribute oil over the ways.
Large automatic clamping vise features adjustable gib guides, removable face plates, and an anti-burr arm.
Self-adjusting, metal chip brush fills removable chip drawer.
Ability to add a programmable feed system to make fully automatic with wide range of capabilities.
Swap cutting head to gain non-ferrous/ferrous option on same saw

Model Options:

Ferrous or Non-Ferrous Cutting Head for mounting
Loading table
Unloading table
575V Transformer

Standard equipment

Blade
Coolant
Saw blade selector calculator
Tools kit for changing blades
Instruction and service manual
Adjustable positive stop

Specifications
Model Number	Euromatic 370S Ferrous
Voltage	220 V/ 440 V, 3-phase
Horsepower	3.5/4.5
Cutting Ability	Ferrous / Non-Ferrous / Plastic
Maximum blade diameter	14-1/2 inch
Maximum vise opening	8-3/4 inch
Maximum feed vise opening	n/a
Maximum Angle	45Â° / 90Â° left / right
Slotting	Yes
Phase	3
Speeds	25/50 rpm
Weight	1,360 lbs
Solid round 90 deg capacity	4-1/4 v
Solid round 45 deg capacity	3-5/8 inch
Tube 90 deg capacity	5-1/16 inch
Tube 45 deg capacity	5 inch
Square 90 deg capacity	4-1/4 inch
Square 45 deg capacity	3-7/8 inch
Rectangle 90 deg capacity	4 x 7 inch
Rectangle 45 deg capacity	4 x 6 inch
Work height	35 inch
Height	73 inch
Width	28 inch
Depth	39 inch

Click here to download manual

Click here to download parts list

Semi-Automatic Cold Saws Model

Euromatic 370S-L Non-Ferrous 14.5 inch blade

Semi-automatic non-ferrous saw that's user friendly for set up and operation. Featuring two removable surface wear plates, heads that rotate 45 deg, three gib guides, and a manual oiler.

440V model requires step-down transformer for operation (part number: 300674)

Features:

Outboard section of the table is designed so shorter lengths tumble down a mesh discharge chute.
Manual oiler to lubricate 1 inch thick, hardened vertical ways.
3.5/4.5 HP motor has the muscle to drive a 14-1/2 inch or 12 inch blade quickly and quietly through solids.
Clear acrylic hood has shock assists for raising and lowering and electrical interlocks.
Table features two removable surface wear plates to support longer cut lengths.
Three gib guides for the cutting head with two adjustable cast iron gib blocks in each for increased cutting accuracy and easy adjustment.
Rear surface of the gearbox is machined with interlocking circles to evenly distribute oil over the ways.
Large automatic clamping vise features adjustable gib guides, removable face plates, and an anti-burr arm.
Swap cutting head to gain non-ferrous/ferrous option on same saw
Ability to add a programmable feed system to make fully automatic with wide range of capabilities.

Model Options:

Ferrous or Non-Ferrous Cutting Head for mounting
Loading table
Unloading table
Roller table
575V Transformer

Standard Equipment:

Blade
Coolant
Saw blade selector calculator
Tools kit for changing blades
Instruction and service manual
Adjustable positive stop

Specifications
Model Number	Euromatic 370S-L Non-Ferrous
Voltage	220 V/440 V, 3-phase
Horsepower	3.5/4.5
Cutting Ability	Non-Ferrous / Plastic
Maximum blade diameter	14-1/2 inch
Maximum vise opening	8-3/4 inch
Maximum feed vise opening	n/a
Maximum Angle	45 deg left
Slotting	No
Phase	3
Speeds	1,500/3,000 rpm
Weight	1,360 lbs
Solid round 90 deg capacity	4-1/4 inch
Solid round 45 deg capacity	3-5/8 inch
Tube 90 deg capacity	5-1/16 inch
Tube 45 deg capacity	5 inch
Square 90 deg capacity	4-1/4 inch
Square 45 deg capacity	3-7/8 inch
Rectangle 90 deg capacity	4 x 7 inch
Rectangle 45 deg capacity	4 x 6 inch
Work height	35 inch
Height	73 inch
Width	28 inch
Depth	39 inch

DAKE Euromatic 370S, 370SA Semi Auto