Dry Cutting: 14"-16" Dry Abrasive Double Mitering Machines
Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated dual chain hold-down vise
Fast, Low Cost Cutting of Hardened Tool Steel, Drills, Reamers,
Bars, Pipe, Angle Iron, Tubing, Flat Stock & Rod.
Capacity: 2" solid 5" pipe
30 - 45 degrees / 1.75" Solids and 3" Most Shapes
Double Mitering Cutting Head can swivel 45 degrees right or left of center. Indicators for 0, 15, 30 and 45
degrees. Cutting head and pedestal are mounted on rugged swinging knee secured in lubricated for life bearings. Lock to hold desired cutting angle is
quick and easy to operate.
|
Cutting Speeds (average) 90°
|
|
Size
|
Material
|
Time
|
|
1"
|
Angle Iron
|
2 sec.
|
|
2"
|
Angle Iron
|
4 sec.
|
|
2"
|
Cold Roll Solid
|
7 sec.
|
|
1.5"
|
Pipe
|
3 sec
|
14"-16" Dry Abrasive Double Mitering Machines
7.5 HP Double Mitering (Left & Right to 45 - 45 degrees, 30, 15, 0 degrees, indicators)
Complete with TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base and air operated dual chain hold-down vise
|
Product #
|
Description
|
|
160441
|
16" DM 7.5 HP 230 VOLT 1 Ph, MAG STARTER
|
|
160442
|
16" DM 7.5 HP 208 VOLT 3 Ph, MAG STARTER
|
|
160443
|
16" DM 7.5 HP 230 VOLT 3 Ph, MAG STARTER
|
|
160444
|
16" DM 7.5 HP 380 VOLT 3 Ph 50HZ, MAG STARTER
|
|
160445
|
16" DM 7.5 HP 440 VOLT 3 Ph, MAG STARTER
|
|
160447
|
16" DM 7.5 HP 575 VOLT 3 Ph, MAG STARTER
|
7.5 HP Double Mitering(Left & Right to 45 - 45 degrees, 30, 15, 0 degrees, indicators) Hydraulic Power Head Models (PH)
Complete with TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base and air operated dual chain hold-down vise
|
Product #
|
Description
|
|
162442
|
16" DM PH 7.5 HP 208 VOLT 3 Ph, MAG STARTER
|
|
162443
|
16" DM PH 7.5 HP 230 VOLT 3 Ph, MAG STARTER
|
|
162444
|
16" DM PH 7.5 HP 380 VOLT 3 Ph 50 HZ, MAG STARTER
|
|
162445
|
16" DM PH 7.5 HP 440 VOLT 3 Ph, MAG STARTER
|
|
162447
|
16" DM PH 7.5 HP 575 VOLT 3 Ph, MAG STARTER
|
7.5 HP Double Mitering (Left & Right to 45 - 45 degrees, 30, 15, 0 degrees, indicators)
Hydraulic Power Head Models (PH)
with patented Wheel Wear Compensator (WWC)
Complete with TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base and air operated dual chain hold-down vise
|
Product #
|
Description
|
|
164442
|
16" DM PH WWC 7.5 HP 208 VOLT 3 Ph, MAG STARTER
|
|
164443
|
16" DM PH WWC 7.5 HP 230 VOLT 3 Ph MAG STARTER
|
|
164444
|
16" DM PH WWC 7.5 HP 380 VOLT 3 Ph 50HZ, MAG STARTER
|
|
164445
|
16" DM PH WWC 7.5 HP 440 VOLT 3 Ph, MAG STARTER
|
|
164447
|
16" DM PH WWC 7.5 HP 575 VOLT 3 Ph, MAG STARTER
|
Abrasive Wheels: Dry Reinforced Abrasive Cutting Wheels
Link for Everett Dry Cut Abrasive Blades
All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.
As a manufacturer of abrasive wheels, we have other grades of wet and dry abrasive wheels to meet your specific requirements. Contact us for special diameter, thickness, arbor hole and drive pin
requirements of abrasive wheels.
Fiberglass Internally Reinforced Resinoid Bond Aluminum Oxide Cutting Wheels
Woven fiberglass cloth is molded in the center of the abrasive wheel for break resistance.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
45FG
|
|
For general purpose cutting
|
|
|
|
|
|
|
|
23020FG
|
|
Designed for use on machines with POWERHEAD (automatic wheel feed) where free cutting ability is needed because of constant feed pressure
|
|
|
|
|
|
|
|
2069FG
|
|
Ideal for heavier wall shapes and tubing
|
|
|
|
|
|
|
|
T32 FG
|
|
For cutting thin wall shapes and thin wall tubing
|
|
|
|
|
|
|
|
GTK-7FG
|
|
Excellent for high quality dry cuts on stainless tubing and other thin wall tubing
|
|
Fiberglass Externally Reinforced Cutting Wheels
Woven fiberglass cloth is applied externally on both sides of the abrasive wheel for break resistance.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
45FGE
|
|
For general purpose cutting
|
|
|
|
|
|
|
|
23020FGE
|
|
Designed for use on cutoff saws with POWERHEAD (automatic
wheel feed) where free cutting ability is needed because of constant feed pressure
|
|
|
|
|
|
|
|
2069FGE
|
|
Ideal for heavier wall shapes and tubing
|
|
|
|
|
|
|
|
T32 FGE
|
|
For cutting thin wall shapes and thin wall tubing
|
|
|
|
|
|
|
|
GTK-7FGE
|
|
Excellent for high quality dry cuts on stainless tubing and other thin wall tubing
|
