Wet Cutting Saws: 20"-22" Wet Abrasive Cutoff Machines
Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated âVâ shaped chain hold-down vise, coolant tray, settling tank and pump
Typical wet cutting speeds are 30 seconds per square inch of material based on application
The cutting wheels on these Everett wet saw models are cooled by rotating through a water box with hinged adjustable sides. The water ejector and the wheel itself combine to
throw the coolant into the cut and over the material to assure total cooling. The flow and discharge are easily regulated with the control valve and by adjusting the sides of the water box.
Capacity: 3" solids. Most 7" shapes
20"-22" Wet Abrasive Cutoff Catalog Page
20"-22" Wet Abrasive Cutoff Machines
Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, coolant tray, settling tank and
pump
|
Product #
|
Description
|
|
201062
|
20" WET 20 HP 208 VOLT 3 Ph, MAG STARTER
|
|
201063
|
20" WET 20 HP 230 VOLT 3 Ph, MAG STARTER
|
|
201064
|
20" WET 20 HP 380 VOLT 3 Ph 50HZ, MAG STARTER
|
|
201065
|
20" WET 20 HP 440 VOLT 3 Ph, MAG STARTER
|
|
201067
|
20" WET 20 HP 575 VOLT 3 Ph, MAG STARTER
|
Hydraulic Power Head Models (PH)
Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated VÂù shaped chain hold-down vise, coolant tray, settling tank and
pump
|
Product #
|
Description
|
|
203062
|
20" WET PH 20 HP 208 VOLT 3 Ph, MAG STARTER
|
|
203063
|
20" WET PH 20 HP 230 VOLT 3 Ph, MAG STARTER
|
|
203064
|
20" WET PH 20 HP 380 VOLT 3 Ph 50HZ, MAG STARTER
|
|
203065
|
20" WET PH 20 HP 440 VOLT 3 Ph, MAG STARTER
|
|
203067
|
20" WET PH 20 HP 575 VOLT 3 Ph, MAG STARTER
|
Hydraulic Power Head Models (PH)
with patented Wheel Wear Compensator (WWC)
Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, coolant tray, settling tank and
pump
|
Product #
|
Description
|
|
205062
|
20" WET PH WWC 20 HP 208 VOLT 3 Ph, MAG STARTER
|
|
205063
|
20" WET PH WWC 20 HP 230 VOLT 3 Ph, MAG STARTER
|
|
205064
|
20" WET PH WWC 20 HP 380 VOLT 3 Ph 50HZ, MAG STARTER
|
|
205065
|
20" WET PH WWC 20 HP 440 VOLT 3 Ph, MAG STARTER
|
|
205067
|
20" WET PH WWC 20 HP 575 VOLT 3 Ph, MAG STARTER
|
Note:
Work Length Gage automatically swings up out of the way when the part is cut.
Abrasive Wheels: Wet Non-Reinforced & Reinforced Abrasive Cutting Wheels
Link for Everett Wet & Dry Cut Abrasive Blades
All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.
As an abrasive wheel manufacturer, we have other grades of wet and dry abrasive cutoff wheels to meet your specific requirements. Contact the factory for special diameter, thickness, arbor hole and
drive pin requirements of abrasive wheels.
Non-Reinforced Rubber Bonded
Cutting Wheels for Wet Cutting
The following cutoff wheels cannot be fiberglass reinforced.
Use only on well guarded machines with extreme caution and personal protection.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
#1410
|
|
For wet metallurgical cutting. Also excellent for high quality wet cuts on hardened material, tubing. Available in most sizes.
|
|
|
|
|
|
|
|
#1115
|
|
Calendered rubber wheel specially formulated for general purpose use on our 10âÃâÃâÃâù wet saw.
|
|
|
|
|
|
|
|
#1329
|
|
General purpose calendered rubber wheel, designed for wet
cutting solids, heavy wall shapes and tubing. Produces fine cut, excellent for use on wet, power head machines. Available in 14", 16", 20", and 26".
|
|
|
|
|
|
|
|
#60
|
|
General purpose pressed rubber wheel designed for wet
cutting solids, heavy wall shapes and tubing. Larger grit sizes generally produce coarser cut than #1329. Available in all sizes.
|
|
|
|
|
|
|
|
#91
|
|
Designed for non-ferrous cutting - copper cutting, brass cutting, etc., rubber bond silicon carbide. Available in all sizes.
|
|
|
|
|
|
|
Fiberglass Reinforced Wet
Abrasive Cutoff Wheels
|
Grade
|
|
Description of Cutting Wheels
|
|
|
93FG
|
|
Fiberglass internally reinforced cloth is molded in the center of the abrasive wheel for break resistance. Pressed resin-rubber abrasive wheel; excellent for high quality
wet cuts on hardened material, also wet metallurgical cutting. Available in most sizes.
|
