Wet Cutting Saws: 26" Wet Abrasive Oscillating Cutoff Machines
COMPLETE with 30 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, oscillation, air operated V shaped chain hold-down vise, coolant tray, settling tank and
pump
Exclusive vibra-action oscillation moves the wheel back and forth while cut is being made. This reduces the area of contact between the wheel and material, resulting in
improved quality of cut, less heat build up, less burr and increased wheel life.
Capacity: 5" solids. Most 7" Shapes
Typical wet cutting saw speeds are 30 seconds per square inch of material based on application.
26" Wet Oscillating Abrasive Cutoff Catalog Page
26" Wet Abrasive Oscillating Cutoff Machines
30 HP Oscillating Models
Complete with TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base, air operated V shaped chain hold-down vise
|
Product #
|
Description
|
|
261272
|
26" WET OSC 30 HP 208 VOLT 3 Ph, MAG STARTER
|
|
261273
|
26" WET OSC 30 HP 230 VOLT 3 Ph, MAG STARTER
|
|
261274
|
26" WET OSC 30 HP 380 VOLT 3 Ph 50 HZ, MAG STARTER
|
|
261275
|
26" WET OSC 30 HP 440 VOLT 3 Ph, MAG STARTER
|
|
261277
|
26" WET OSC 30 HP 575 VOLT 3 Ph, MAG STARTER
|
30 HP Oscillating Hydraulic Power Head Models (PH)
Complete with hydraulic power head, TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base, air operated V shaped chain hold-down vise
|
Product #
|
Description
|
|
263272
|
26" WET OSC PH 30 HP 208 VOLT 3 Ph, MAG STARTER
|
|
263273
|
26" WET OSC PH 30 HP 230 VOLT 3 Ph, MAG STARTER
|
|
263274
|
26" WET OSC PH 30 HP 380 VOLT 3 Ph 50 HZ, MAG STARTER
|
|
263275
|
26" WET OSC PH 30 HP 440 VOLT 3 Ph, MAG STARTER
|
|
263277
|
26" WET OSC PH 30 HP 575 VOLT 3 Ph, MAG STARTER
|
30 HP Oscillating Hydraulic Power Head Models (PH)
with patented Wheel Wear Compensator (WWC)
Complete with hydraulic power head, TEFC motor, magnetic starter with 110 volt at the pushbuttons, cabinet base, air operated V shaped chain hold-down vise
|
Product #
|
Description
|
|
265272
|
26" WET OSC PH WWC 30 HP 208 VOLT 3 Ph, MAG STARTER
|
|
265273
|
26" WET OSC PH WWC 30 HP 230 VOLT 3 Ph, MAG STARTER
|
|
265274
|
26" WET OSC PH WWC 30 HP 380 VOLT 3 Ph 50 HZ, MAG STARTER
|
|
265275
|
26" WET OSC PH WWC 30 HP 440 VOLT 3 Ph, MAG STARTER
|
|
265277
|
26" WET OSC PH WWC 30 HP 575 VOLT 3 Ph, MAG STARTER
|
Abrasive Wheels: Wet Non-Reinforced & Reinforced Abrasive Cutting Wheels
Link for Everett Wet & Dry Cut Abrasive Blades
All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.
As an abrasive wheel manufacturer, we have other grades of wet and dry abrasive cutoff wheels to meet your specific requirements. Contact the factory for special diameter, thickness, arbor hole and
drive pin requirements of abrasive wheels.
Non-Reinforced Rubber Bonded
Cutting Wheels for Wet Cutting
The following cutoff wheels cannot be fiberglass reinforced.
Use only on well guarded machines with extreme caution and personal protection.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
#1410
|
|
For wet metallurgical cutting. Also excellent for high quality wet cuts on hardened material, tubing. Available in most sizes.
|
|
|
|
|
|
|
|
#1115
|
|
Calendered rubber wheel specially formulated for general purpose use on our 10ÃÂÉ¢ÃÂÉâÂÄÂöÃÂÉâÂÄÂûÃÂÉâÂÄÂöÃÂɹ wet saw.
|
|
|
|
|
|
|
|
#1329
|
|
General purpose calendered rubber wheel, designed for wet
cutting solids, heavy wall shapes and tubing. Produces fine cut, excellent for use on wet, power head machines. Available in 14", 16", 20", and 26".
|
|
|
|
|
|
|
|
#60
|
|
General purpose pressed rubber wheel designed for wet
cutting solids, heavy wall shapes and tubing. Larger grit sizes generally produce coarser cut than #1329. Available in all sizes.
|
|
|
|
|
|
|
|
#91
|
|
Designed for non-ferrous cutting - copper cutting, brass cutting, etc., rubber bond silicon carbide. Available in all sizes.
|
|
|
|
|
|
|
Fiberglass Reinforced Wet
Abrasive Cutoff Wheels
|
Grade
|
|
Description of Cutting Wheels
|
|
|
93FG
|
|
Fiberglass internally reinforced cloth is molded in the center of the abrasive wheel for break resistance. Pressed resin-rubber abrasive wheel; excellent for high quality
wet cuts on hardened material, also wet metallurgical cutting. Available in most sizes.
|
